空调扇出现故障怎么办——不能制冷
What to do if the air conditioning fan malfunctions - unable to cool
1、检查水泵是否工作,如果不抽水,先检查线路断了没。
1. Check if the water pump is working. If it is not pumping, first check if the circuit is disconnected.
2、平时使用可以先用冰水打湿冰帘后在安装,这样出风效果会好一点。
2. Usually, you can wet the ice curtain with ice water before installing it, which will improve the ventilation effect.
3、检查绿色冰帘是否打湿,如果倾斜或者没安装好也会出现这样的现象。
3. Check if the green ice curtain is wet, and this can also occur if it is tilted or not installed properly.
二、空调扇出现故障怎么办——漏水
2、 What to do if the air conditioning fan malfunctions - water leakage
1、检查水箱,看水箱是不是破损。
1. Check the water tank to see if it is damaged.
2、底部的塞子没安装好,引起了漏水。
2. The plug at the bottom was not installed properly, causing water leakage.
3、还有种就是 水槽 支架断裂导致水槽倾斜漏水。
3. Another possibility is that the bracket of the sink breaks, causing the sink to tilt and leak water.
4、冰帘没安装好,水从水槽孔滴下来沿着冰帘溅射到空调扇后盖,累积水珠滴出来了。安装正确可以解决好问题。
4. The ice curtain was not installed properly, and water dripped down the sink hole and splashed along the ice curtain onto the back cover of the air conditioning fan, causing accumulated water droplets to drip out. Installing correctly can solve problems.
5、检查抽水泵,看抽水泵的上的橡皮管是不是破损或者接口处没安装好。可以替换或者包扎好接口处解决问题。
5. Check the water pump to see if the rubber hose on the pump is damaged or if the interface is not properly installed. You can replace or wrap the interface to solve the problem.
三、空调扇出现故障怎么办——不出风或者风小
3、 What to do if the air conditioning fan malfunctions - no air or low air flow
1、风扇是坏的话就是是电机本身的问题。这个稍微麻烦一点,需要换电机的。近的话发回来换,远的话尽量发个电机过去装下就好了。
1. If the fan is faulty, it is a problem with the motor itself. This is a bit troublesome, it needs to be replaced with a new motor. If it's close, send it back for replacement. If it's far, try sending a motor over and installing it.
2、看风力是不是吸进去的感
泥杆 保定古筝 塑料增韧剂 拱形护坡模具 保定空调维修 托辊生产线觉,反面有风的话可能是风扇电机的线接错了,可以调节电机的接触线就可以解决,大概10~30不等可以弄好。可能是控制面板下面的转轴挡着出风口破裂了。
2. Check if the wind force feels like it is being sucked in. If there is wind on the opposite side, it may be due to the wrong wiring of the fan motor. You can adjust the contact wire of the motor to solve the problem, which can vary from 10 to 30 degrees. It may be that the rotary shaft under the control panel is blocking the air outlet and breaking.